유럽 지역에서 접속하신 것 같습니다.
다음에서 쇼핑하시겠습니까? webike.eu.com?
(0)
11 리뷰 보기 유형:
- 리어 액슬 너트 커버작성자 AELLA호환:
- KAWASAKI ZX-25R 21-
- KAWASAKI ZX-4R 23-
- KAWASAKI ZX-4RR 23-
The search for just my Kawasaki zx25r had all the parts i needed, from all japanese brands and even more that I didnt know what it was for... Products arrived on time and now im going to use my points...더 보기 - 리어 액슬 너트 커버작성자 AELLA호환:
- KAWASAKI ZX-25R 21-
- KAWASAKI ZX-4R 23-
- KAWASAKI ZX-4RR 23-
As the title says, I bought this because it was a hassle to replace the split pin every time, but the fit is quite severe, and if the Washer on the Axle Shaft is even slightly off, the Cap will not go...더 보기 - 리어 액슬 너트 커버작성자 AELLA호환:
- KAWASAKI ZX-25R 21-
- KAWASAKI ZX-4R 23-
- KAWASAKI ZX-4RR 23-
The product arrived and I installed it as soon as possible.Refreshingly improved the look. The installation required a little hang, and it was a point when passing through the hole under the body.더 보기 - 호환:
- YAMAHA Bolt CSpecifications B33
- YAMAHA Bolt CSpecifications B339
- YAMAHA SCR950
Adds a little class to the motorcycle. Easy to install. Apply pressure to the top of the cap when tightening the set screw so the alignment does not change. Be careful when first inserting the set scr...더 보기 - 리어 액슬 너트 커버작성자 AELLA호환:
- KAWASAKI ZX-25R 21-
- KAWASAKI ZX-4R 23-
- KAWASAKI ZX-4RR 23-
I used plastic and rubber for some parts, but it's too small to replace. It is also a simple Slider, and I think that it is easy to put on and take off and is good.더 보기 - 호환:
- DUCATI HyperMotard 1100 HyperMotard 1100
- DUCATI HyperMotard 796 HyperMotard 796
- DUCATI HyperMotard 821 HyperMotard 821
- DUCATI Monster 1100 Monster 1100
- DUCATI Monster 796 Monster 796
- ...외 다수.
Wheel nut is changed to Black, and it is changed together.Coloring is of course Black.The lock pin itself is just to stop it from loosening, but since it is made by AELLA, it is made of high quality S...더 보기 - 호환:
- HONDA CBR250R (MC41) CBR250R (MC41)
I gave it to the Motorcycle shop to have it replaced along with the Tire replacement. It's longer than the OEM Bolt and sticks out a little too far for me to install. I was toldApplicable car models a...더 보기 - 액슬 엔드 캡 고무작성자 KIJIMA호환:
- HARLEY-DAVIDSON SPORTSTER FORTYEIGHT SPORTSTER FORTYEIGHT 2011
- HARLEY-DAVIDSON XL883L [Sportster] XL883L [Sportster] Year: 2011
- HARLEY-DAVIDSON XR1200 XR1200
This is a cheap and easy way to improve the look of the Axle end, which looks like a bare steel pipe. It's just a simple fit, but it's ExactlyFit so it's unlikely to come off.더 보기 - Since Slider is expensive and can not be purchased, I bought it with aiming for damage prevention and Dress-up effect at the time of fall.Somewhat, it is aim of Dress-up.If it is 19 mmNut, I think tha...더 보기
- It is for MONKEY, but you can install it to APE without problem.If Nut's Size is 19 mm, there is no problem.I installed it for self-satisfied Dress-up and for insurance when I fell down.I want the...더 보기
- 액슬 엔드 캡 고무작성자 KIJIMA호환:
- HARLEY-DAVIDSON SPORTSTER FORTYEIGHT SPORTSTER FORTYEIGHT 2011
- HARLEY-DAVIDSON XL883L [Sportster] XL883L [Sportster] Year: 2011
- HARLEY-DAVIDSON XR1200 XR1200
I am on XL 883 N but Black is going to buy for goal. It's easier than OEM Product and it's not that bad. When you wipe CRC when inserting you can install Smooth.더 보기
?
일본
최대 쇼핑몰
전용 쿠폰,
세일
빠르고, 안정적인
배송