Custom Air Filter Oval Tapered Type

Fast delivery !!I use Yoshimura TMR32 carburetor, with KN high flow air filter,Engine response is very good, the interface size is correct, no other ancillary installation.---運送速度很快!! 我用在吉村TMR32化油器 , 搭配KN高流量空氣濾清器,引擎反應它馬的好 , 接口尺寸也正確 , 安裝時不需其他輔助 .

Very bright and shiny part and it's colorway fits nicely with Yoshimura MJN-TMR carburetors that I have in my Honda CB900F. Very fast delivery time also!

It's in use on the KZ1000J
When I replaced the OEM carburetor with the KEIHINCRSPECIAL Knife I installed it instead of the OEM Air cleaner
I wasn't sure if I should ride as Funnel or put a Filter on it, but the activity Area is a lot of wind I decided to put it on because it's an area
K&N is a manufacturer with a proven track record, so you can rest assured that you're in good hands I like the fact that it can be used repeatedly with proper maintenance

Active (Mikuni) or PMC power filter adapter
51Φ this Funnel in the caliber will fit
Speaking of Power Filter, it's a K&N Image, so
I've installed it
Isn't that a little too high?
I feel that
It used to be about 4-5 thousand yen for an Image
Right now it's 1pc.8,000 over
I think the stuff is good
With four rounds, you need four, so it's a pretty painful expense

Unless you're a stickler for it
The air filter from PMC called SmoothSTREAM is called
I felt that it was good because it was otherwise solidly made

But when it comes to air filters, K&N's Image is so strong
I would buy K&N
BrandName is a Large thing

Since the plating part of the plating type is noticeable, I painted it Matte Black Installed

I bought a PMC Smooth STREAM air filter the other day
It was interfering with the Frame a little bit, so I tried to dodge it completely
We've been around for a long time, and we're an old school air filter
I chose K&N because it gives me a sense of security and certainty
From OEM Compatibility to Universal
The Lineup is so complex that it's hard to know which one to choose!
And I feel like the prices have gone up quite a bit (It was about $4,000 Image in my opinion.)
The RU-3010 that I purchased this time is
Oval taper type with 54mm diameter and a phi; insertion diameter
RU-0981
RU-3000
RU-3010
There are three types of the same shape as
The difference is in the Offset
If you look at the PLOT notation, it's only marked as A.B.C Type
We don't know what it's like...
4Quantity by RU-0981:I guess that there is no Offset because there is a Variation of Set
The problem was 3000 and 3010
Although AMAZON's description says 3mm Offset
Not sure what kind of Offset it is
So, in a sense, I took a gamble and bought the 3010 one
As a result, the RU-3010 is the one with 3mm offset to Left

RU-0981 A Center
It may be useful to install the 3mm Offset on the RU-3000 B Right side
It may be useful to install the 3mm Offset on the first side of RU-3010 C Left
Will be

if the carburetorBitch is a narrow 4-shot
Quantity A:2pc. Set
1pc. each of B and C will allow the air cleaners to cross paths with each other
You may be able to change it with Offset if the installation space is too small
I wanted something dodged in Left and the RU-3010 was the right choice

It's a product that neither the import agent nor WEBIKE explained well enough
If you need Offset, I hope this information is helpful!