유럽 지역에서 접속하신 것 같습니다.
다음에서 쇼핑하시겠습니까? webike.eu.com?
66,833.78 KRW (7,200 JPY)
배송 정보
재고 있음 : 2개 남음, 배송까지 24 시간.
예상 도착일
BALIUS [BALIUS] I B1
91-00
BALIUS [BALIUS] I B1-B4
91-00
BALIUS [BALIUS] II B1
91-00
BALIUS [BARIOS] II B4
91-00
전미 및 유럽 각국에 20년 이상 장기간에 걸친, 100만개 이상의 판매 실적이 나타내는 대로 고속 주행에 없어서는 안 된다 조종 핸들 부품입니다. 특히 고속 도로, 경기장에서 고속 주행에는 안전성 면에서도 특히 필요 부품입니다.
[특징]
*상 테이퍼 베어링에 구성되어 있으므로 처리에 오래 되어 상태나 나빠질 없습니다.
*스틸 볼과 다른 그리스 조각의 녹이 발생하지 않습니다. 베어링 면적을 확대하고 원활한 핸들 조작이 가능합니다.
*특수강을 사용하고 있어 내마모성과 내 피로 강도를 높이는 한번의 교환으로 반 영구적으로 사용이 불가능합니다.
*스틸 볼의 경우, 차체 및 주행 하중은 점에서 받고 있었기 때문에 가혹한 사용에 견디지 못해가타이 발생하기 쉽습니다.
*스티어링 댐퍼를 얻어도, 헤드 콘이 원활한 작용을 하지 않고서는 아무런 의미도 없고, 고속 주행의 경우 안정성에도 의문이 생깁니다. NHK의 스티어링 댐퍼과의 병용으로 핸들의 부침이 완전히 사라지고, 훌륭한 핸들링 감각을 즐길 수 있습니다.
주의사항
* 사용 설명서가 포함되어있는 경우, 일본어로 표기됩니다.
이미지 포함 리뷰
호환성:KAWASAKI BALIUS I B4 91-00, KAWASAKI BALIUS [BALIUS] I B1 91-00, KAWASAKI BALIUS [BALIUS] I B1-B4 91-00, KAWASAKI BALIUS [BALIUS] II B1 91-00, KAWASAKI BALIUS [BARIOS] II B1-B4 91-00
May 1, 2012
Since the Ball bearing of the NORMAL was cracked and that it was a Motorcycle by which a Handle blurs easily from the first does not need to spill an exchange
? [ kana / which was reduced for a while ]
Ball to a Taper roller.The place where a Maintenance tends to carry out it is good. Since the Dust seal of the
NORMAL cannot be used, frequency goes up.
호환성:KAWASAKI BALIUS I B4 91-00, KAWASAKI BALIUS [BALIUS] I B1 91-00, KAWASAKI BALIUS [BALIUS] I B1-B4 91-00, KAWASAKI BALIUS [BALIUS] II B1 91-00, KAWASAKI BALIUS [BARIOS] II B1-B4 91-00
Feb 27, 2012
Although it was dreadful before exchange for a handle to have blurred extremely and to have operated at 60~80 km,
Since I had this attached at a shop, and there was firm touch even if it was as handle 謠｡ whether blur of a handle was completely lost and also rigidity went up, it can have operated in comfort! It was good to buy it!
호환성:YAMAHA DT125 A-H 74-81, YAMAHA DT125 LC 82, YAMAHA DT175 A-C 74-76, YAMAHA DT175 F-H 79-81, YAMAHA DT250 B-F 75-79
Aug 4, 2021
A lot of Yamaha bikes are ball type, which is fine from a handling point of view, but the MAJESTY125 has a lot of Stem gurgling problems!
So, I replaced it with this product of high durability.
Of course, the new one works great and is now normal from the dizzy Handling that seemed to mock up.
However, the replacement work is very Large strange, Top level so far (Large strange in a sense than full Overhaul by taking down the Engine)
It's not the kind of difficulty that can be managed with tools, and beating the Race is a feat of strength.
Of course, after all the rods around the front, we had to fight with the bearings for a few hours, and the race press fitment was also very careful.
If you don't know what you're doing, it's best to take it to a shop, because you won't be able to return it to its original state and take it to a motorcycle shop.
호환성:SUZUKI RM125 79-80, SUZUKI RM200 79-80, SUZUKI RM400 79-80, YAMAHA FJ600 H-K 84-85, YAMAHA FZ250 FAZER
May 13, 2020
I'll believe in "Made in Japan quality"!
Frame headPipe Outer for under bracket bearing on the underside The process of typing lace was a battle with anxiety … Han Merlingu typing in is noisy (Neighborhood nuisance.) I was so scared because the position where the outer lace stops is so far back Is there any mistake in the parts? Is it possible that the handlebar is not turned off due to contact with the pipe?
The inner diameter of the outer lace is thinner than the diameter of the inner wall of the head pipe, so remove it again There are no dents in the bearing Also, when the bearing is worn out, the bearing's wall thickness is not in contact with the bearing's thickness, making it inoperable hellip; I was so worried
On the way, I tried to apply the Under bracket; Because it was not possible to turn back, I continued typing as it was
…As a result, the installation is complete I did We'll run for a while and see what happens It was a windy day, but the neck root (Stem) The feeling of rigidity transmitted from the car is increased and the car becomes stable and fun to drive
I think you should ask Shop to do the work for you
호환성:SUZUKI RM125 79-80, SUZUKI RM200 79-80, SUZUKI RM400 79-80, YAMAHA FJ600 H-K 84-85, YAMAHA FZ250 FAZER
Mar 31, 2016
When you cut Handlebar there is a catch,
As I was concerned, I watched everyone's impressions and purchased
Carefulness is required for exchange, but take time
I think I can do it if I try
Let's ask Shop for those who do not have themselves
It is satisfying with Smooth operation feeling after exchanging
리뷰 상세
